Slipped Capital Femoral Epiphysis (SCFE ) Screw System
Slipped capital femoral epiphysis (SCFE) is a common hip disorder in the pediatric population in which the femoral epiphysis displaces from the metaphysis through the physis. The standard of care for SCFE is insitu fixation with a single cannulated screw. The use of standard cannulated screws became an issue due to the difficulty in removal, which has become more important because of the increasing number of hip preservation procedures (open hip dislocations) performed in SCFE for impingement.
The SCFE screw system has been designed specifically for the treatment of SCFE and offers greater advantage for fixation compared to standard cannulated screws. The SCFE screw system is also indicated for fracture fixation of large bones and large bone fragments, pediatric femoral neck fractures, intercondylar femoral fractures, and sacroiliac joint disruptions. Further indications may be tibial plateau fractures, ankle arthrodesis, and subtalar arthrodesis.
Oval shaped washers are available for use in patients with poor bone quality to prevent countersinking of the screw head, allowing for greater screw angulation (up to 55) as well as 1 mm and 2 mm adjustments in screw positioning. The set includes the existing 2.8 mm guide wire that is 450 mm long and consists of a cobalt based material to provide additional stiffness and resistance to bending.
Specific instrumentation has been developed to aid in percutaneous insertion/removal of the screws. The new instruments include a 5.0 mm core/7.3 mm cannulated, and calibrated shaft-stepped drill bit, and 420.5 mm long. Additionally, the existing drill stop can be used with the drill bit.
A new trocar has been designed with a sharp tip allowing for easier insertion through the soft tissue, which helps to secure bone contact. The protection sleeve has been designed to interface with the new trocar.
A cannulated direct measuring device, allowing screw length to be measured off of the guide wire, is also included.
The 7.3 mm SCFE screw is compatible with the T40 StarDrive screwdriver which is also cannulated, and 350.5 mm long.
The SCFE screw is a 7.3 mm stainless steel cannulated shaft screw. The screw lengths range from 45130 mm, in 5 mm increments and screws are self-tapping.
A boy aged 11 years and 3 months presented with a limp and had had pain in the thigh for 8 weeks.
Case provided by Richard Reynolds, Detroit, USA
Hazards and labeling
Due to varying countries’ legal and regulatory approval requirements, consult the appropriate local product labeling for approved intended use of the products described on this website. All devices on this website are approved by the AO Technical Commission. For logistical reasons, these devices may not be available in all countries worldwide at the date of publication.
This work was produced by AO Foundation, Switzerland. All rights reserved by AO Foundation. This publication, including all parts thereof, is legally protected by copyright.
Any use, exploitation or commercialization outside the narrow limits set forth by copyright legislation and the restrictions on use laid out below, without the publisher‘s consent, is illegal and liable to prosecution. This applies in particular to photostat reproduction, copying, scanning or duplication of any kind, translation, preparation of microfilms, electronic data processing, and storage such as making this publication available on Intranet or Internet.
Some of the products, names, instruments, treatments, logos, designs, etc referred to in this publication are also protected by patents, trademarks or by other intellectual property protection laws (eg, “AO” and the AO logo are subject to trademark applications/registrations) even though specific reference to this fact is not always made in the text. Therefore, the appearance of a name, instrument, etc without designation as proprietary is not to be construed as a representation by the publisher that it is in the public domain.
Restrictions on use: The rightful owner of an authorized copy of this work may use it for educational and research purposes only. Single images or illustrations may be copied for research or educational purposes only. The images or illustrations may not be altered in any way and need to carry the following statement of origin “Copyright by AO Foundation, Switzerland”.
Check www.aofoundation.org/disclaimer for more information.
If you have any comments or questions on the articles or the new devices, please do not hesitate to contact us.
"approved by AO Technical Commission" and "approved by AO Foundation"
The brands and labels "approved by AO Technical Commission" and "approved by AO Foundation", particularly "AO" and the AO logo, are AO Foundation's intellectual property and subject to trademark applications and registrations, respectively. The use of these brands and labels is regulated by licensing agreements between AO Foundation and the producers of innovation products obliged to use such labels to declare the products as AO Technical Commission or AO Foundation approved solutions. Any unauthorized or inadequate use of these trademarks may be subject to legal action.